QSC GXD 4 Power Amplifier
QSC GXD 4 Power AmplifierDetails
Product Ref: 56164View Full Description
Full DescriptionView Full Description
GXD Series amplifiers are ideal for entertainment and production applications requiring performance and the convenience of integral signal processing. The hallmarks of the QSC brand - professional audio quality, engineering and manufacturing focused on long-term reliability - are all intrinsic to GXD. Add contemporary styling, multiple routing options, light weight, digital signal processing and advanced protection circuitry, and the GXD Series clearly represents real value - something everyone can use.
The GXD series is optimised for use with 8 and 4 ohm loudspeaker loads. GXD amplifiers deliver just the right amount of power to the most popular speakers used by entertainers and production professionals.
The Right Power
There's a GXD amplifier within 1dB of the ideal power for your speaker system. Best practice is to use an amplifier capable of delivering approximately twice the loudspeaker's rated power capacity. Too little amplifier and the speakers won't deliver everything they're capable of and the risk of destructive amplifier clipping is increased. Too much power probably means unnecessary amplifier expense.
To determine the power points for the GXD series, QSC examined the loudspeakers most widely used for sound reinforcement by musicians, DJs and production professionals. Overall, these speakers are equipped with woofers that fall into a couple of categories of continuous power capacity - low-power drivers that can handle 150 - 250 watts, and mid to high-power drivers rated around 250-400 watts. Single woofer loudspeaker systems using these drivers will typically have an impedance of 8ohm. Dual woofer loudspeakers will, of course, have power ratings that are two times that of the single woofer model and an impedance that is half that of single-woofer models.
Digital Signal Processing
The GXD amplifiers are unlike other amps in this category that provide little more than a front panel screen to control the same functions that have been under rear-panel, DIP switch control for decades. The GXD amps bring full-function loudspeaker processing capability to a new price point with all the processing necessary to get the most from a loudspeaker system. The DSP section includes High and Low-Pass filters (24dB LR), 4-band parametric equalizer, signal alignment delay, and RMS/Peak speaker protection limiting. Twenty presets for selected typical systems are provided as generic "starting points" are included.
The most common cause of loudspeaker failure is amplifier clipping. The digital limiter used in the GXD amplifiers is set to prevent the amplifier from being driven into clipping while delivering the maximum usable output. In addition to amplifier limiting it also provides smart speaker protection by simply setting the loudspeaker's continuous power and impedance (4ohm and 8ohm), and selecting whether Mild, Medium or Agressive protection is desired.
- High peak output power - up to 1600 Watts
- Power levels matched to the most popular loudspeakers and optimised for maximum real-world headroom into 4ohm and 8ohm speaker systems.
- Class-D output stage with a universal power supply for high performance and efficiency.
- Extensive and powerful loudspeaker processing built in. Includes High & Low-Pass filters, 4-band PEQ, Limiting, and Delay.
- Large LCD display simplifies amplifier setup and indicates amp status.
- Inputs: Parallel XLR and 1/4" TRS connectors for compatibility with any source while providing convenient loop-thru capability.
- Precision rotary encoders for gain and DSP parameter control.
- Outputs: Professional binding post and NL4 connectors (compatible with NL2) provide for mono and bi-amp speaker connections.
- Digital Limiting automatically protects the amplifier from damage due to temperature rise or overdrive.
- Adjustable speaker protection to match your loudspeaker's power and impedance.
- Front panel LEDs indicate signal presence, input overload, and amplifier clipping.
Stereo Mode - Watts per channel
- 8 ohm dynamic, both channels driven: 600 W
- 4 ohm dynamic both channels driven: 800 W
- 8 ohm continuous, both channels driven: 400 W
- 4 ohm continuous both channels driven: 600 W
- Distortion (1 kHz at full rated power): < 1% THD
- Signal to Noise (A weighted, 20 Hz - 20 kHz): 100 dB
- Input Sensitivity: 1.2 Vrms, 3.9 Vrms
- Voltage Gain (8 ohm): 33.5 dB
- Output Circuitry: Class D
- Power Requirements (1/8 power at 4 ohm):
- - 100 Vac: 3.4 Amps
- - 120 Vac: 2.9 Amps
- - 230 Vac: 1.6 Amps
- Frequency Response: 20 Hz - 20 kHz, +0.7 dB, -0.8dB
- Dynamic Headroom (4 ohm): 1.25 dB
- Damping Factor: 100
- Input Impedance (ohms): 20k (balanced), 10k (unbalanced)
- Maximum Input Level: +23.5 dBu
- Input Connectors (each channel): 3-pin XLR/F / 1/4" TRS, balanced
- Output Connectors (each channel): NL4 (Channel 1 - 1+/-, Channel 2 - 2+/-), binding posts
- Amplifier and Load Protection: Short circuit, open circuit, thermal, RF protection, Load protected against DC faults
- Front Panel Controls and Indicators:2 x Rotary Encoders, 3 x Operational buttons (HOME, ENTER, EXIT), 2 x Green Signal LEDs, indicate signal presence, 2 x Red A/D Clip LEDs, indicate input over-drive and/or amplifier current clipping, Blue Power LED ring, AC on, 2.12" x 1.0", 256 x 128 pixel LCD
- DSP Functions: High Pass Filter, 4th order LR, adjustable Frequency 20 Hz to 4 kHz, Low Pass Filter, 4th order LR, adjustable Frequency 60 Hz to 4 kHz, 4-band PEQ, with variable Frequency, Gain, and Bandwidth, Peak Limiter, with Power, Agressiveness, and Impedance selection, Delay 50 msec max.
- Dimensions (HWD): 3.5" (2 RU) x 19" x 10.2" (89 mm x 483 mm x 259 mm)
- Weight Net: 11.3 lb (5.1 kg), Shipping: 15.4 lb (7.0 kg)
- Agency Approvals: UL, CE, RoHS/WEEE compliant
- Includes: Power cable, and quick start guide
The product price includes 2 years' warranty and 30 day money back guarantee.
However, the Gear4music extended warranty scheme provides an enhanced service, and is designed to offer a higher level of protection than many 'free' warranties offered by some retailers and manufacturers.
The highlights of this enhanced warranty service are:
- Warranty is extended to 6 years from the date of delivery.
- Our Money Back guarantee is extended from 30 days to 180 days (terms apply after 30 days)
- Collection and delivery costs are included for the first 2 years
- Claim 50% cash back on the cost of the policy after 6 years if it has not been used!
- Warranty is transferable if the item is re-sold
- Loan or replacement equipment will be provided if the product isn't repaired within 30 days
- If an item can not be repaired, a similar alternative product or cash discount (as defined in this policy) will be offered
- The policy can be cancelled within 30 days, and at any time after that for a pro-rata discount
Please note that this extended warranty is currently only available on products sold within the EU or EEA, and is subject to the terms and conditions as detailed on the extended warranty certificate provided.
For customers in outlying areas of the country, the price of the Extended Warranty may be marginally higher, due to the potential for higher collection and redelivery transport costs.
This enhanced warranty is in addition to the standard Gear4music and manufacturer warranty policies, and the Gear4music terms and conditions of trade. No statement or condition of sale contained within these terms affects or restricts your statutory rights as defined under the Consumer Contracts Regulation 2014.
All Products are new unless stated, and include a minimum of 2 years warranty.
- CDs & DVDs
- In-ear Monitors
- Earplugs and Ear Protection
- Mouthpieces, Reeds etc… for Woodwind and Brass instruments
- Mouth / Lip Care Products
If you also purchase items that do not qualify for free delivery, some delivery charges may be applied to your order which will be shown in your shopping basket.